Choose Your Car Model – Varna Rat Repellent Installation

August 6th, 2014

Please click the below models to see visual pictures to install “Varna Suraksha Rat Repellent – Auto Model”

repeller

Rat Entered the Passenger Compartment Destroying Seats? Varna Ultrasonic Repellent Already Installed in Engine Bay

June 4th, 2021

The rats primarily damage the parts in the engine bay and visit the engine bay regularly through the wheel well. But they cannot enter the car passenger or compartment as the car cabin is completely sealed by the car manufacturer. Here, the rats makes a entry by nibbling the air vent or any other soft entry point and gaining a passage to the passenger area. This usually happens when there is food littering within the car, and rats try to make a way to eat and succeed.

rat-damage1

rat-damage-5

 

Once the rats enter the cabin, it destroys the interiors or seat etc. as below

rat-damage-2

The Ultrasonic Device repellent installed in the engine bay will not stop rats entering the passenger cabin. Rats quickly enter through Ultrasonic area and gain entry to the cabin. So, the ultrasonic repellent cannot stop them passing by within few seconds.

What can be done now?

Step 1 : Place glue traps on floor mats to capture the rats which may reside in the car dashboard.

rat-damage-4

rat-damage-3

Step 2 : Repair or replace the damaged part of the car where rats are entering. Fix all the entry points where rats have created.

Step 3 : PLEASE DO NOT allow anybody to eat inside the car or clear the food items every night before exit from the car.

 

PLEASE NOTE:

Ultrasonic Repellent Device will protect only the engine bay by producing ultrasonic waves within the engine bay, once the rat gains entry to the passenger cabin, you will have block the entry by fixing the damaged part and flush out the rats which have already gained access inside the car cabin.

 

Varna Ultrasonic Rat Repellent For Renault Kwid

August 5th, 2020

Skoda Laura – Varna Rat Repellent Installation

March 28th, 2016

Varna Rat Repellent installation pictures for Skoda Laura.

laura-skoda03

The rat repellent has to be faced towards the bonnet hood for reflecting the sound throughout the engine bay.

laura-skoda

Stick aluminium sticker provided by us when there is foam pad within the hood. This will help to reflect the sound 100% efficiently.

laura-skoda02

Connect Red Wire crocodile pin to Positive terminal and Black wire to negative terminal of the battery.

laura-skoda04

Atleast make sure if there is 5 – 8 inches clearance is there between repellent and hood.

Repellent-Height2

You will hear beep audible sound once you connect to the battery while pressing “TEST” button, it means it is functional now.

Testimonial Mail by Aerospace Lab – Varna Suraksha VX Model Review

March 5th, 2016

Please go through email sent by our customer –

Sir,

Last time we purchased and installed your products and we are very satisfied about the results. Again we would like to purchase the same repellent system in our organisation. Kindly supply and install the VARNA SURAKSHA VX model quantity 3 units along with the bill and invoice. Payment will be made through cheque.

Looking forward to your positive and timely response.

Regards,
MACHINE SHOP,
A.P.M.F DIVISION
NATIONAL AEROSPACE LABORATORIES,
OLD AIRPORT ROAD
KODIHALLI,
BANGALORE-560017

Volkswagen Jetta – Varna Rat Repellent Installation

January 5th, 2016

Quick Installation explained for Volkswagen Jetta –

Fix the unit inside the Bonnet, visibly outside, SPEAKER FACING UPWARDS to rebound the ultrasonic sound throughout the bonnet area evenly. (Please make sure the speaker is not obstructed and do not hide between any engine area.)


jetta1

Red Wire has to be connected to Positive Terminal & Black Wire has to be connected to Negative Terminal of the Car Battery (12 Volt battery power is required, you may also draw power from any wire which is passing power)

 

jetta2

Please check the unit functionality by pressing “TEST”, you will hear a loud sound.

jetta3

If your car bonnet lid has heat insulation or heat proof layer (when you open your car bonnet you can see the black layer), face the speaker towards the engine metallic area to re-bounce the ultrasonic sound evenly throughout the engine area.

Rodent Master Controller & Transducer Installation Video

November 19th, 2015

Click “Full Screen” in the bottom right hand side of the video, for clear view.

Cruze Chevrolet – Varna Car Rat Repellent

November 14th, 2015

Easy Steps to install Varna Suraksha Car Rat Repellent for Cruze Chevrolet

  • Focus the repellent towards the hood and tie the unit firmly with provided plastic tags and support.cruz01
  • Connect red wire to positive terminal and black wire to negative terminal.
  • You can see red light flickering and hear beep sound when “Test” button is pushed.

cruz02

Stick the aluminium sticker to the hood if you have insulation foam for better reflection of ultrasonic sound throughout the engine bay.

cruz03

X-Trail Nissan – Fixing Varna Ultrasonic Rat Repellent

November 5th, 2015

 

Simple picture guide to install Varna Ultrasonic Rat Repellent for X-Trail Nissan car.

xtrail01

Face the Varna rat repellent facing towards the bonnet hood to reflect the sound throughout the engine bay. If your car has insulation foam within the hood, you may have to stick aluminium sticker to reflect the sound 100%.

 

xtrail02

Connect the red wire to positive terminal of the battery and black wire to negative terminal of the battery. The unit will be functional, you can see red light flickering.

 

Skoda Rapid – Varna Ultrasonic Rat Repellent Installation

November 5th, 2015

Simple picture guide to install Varna Ultrasonic Rat Repellent for Skoda Rapid car.

 

rapid01

Face the repellent towards the bonnet hood to reflect the sound throughout the engine bay. If your car has insulation foam within the hood, you may have to stick aluminium sticker to reflect the sound 100%.

 

rapid02Connect the red wire to positive terminal of the battery and black wire to negative terminal of the battery. The unit will be functional, you can see red light flickering.

Hyundai-xcent – Varna Rat Repellent

November 3rd, 2015

Simple steps to fix Varna Ultrasonic Rat Repellent for Hyundai xcent car

xcent

Fix the repellent facing towards the bonnet with the help of plastic tags provided.

xcent2Connect red wire to positive terminal and black wire to negative positive. You will the red light flickering and hear loud beep sound when “TEST” button is pressed. The unit is functional now.